![]() ![]() 5 In Global stock for delivery within 5 working day(s) Add to Basket. 9 In AU stock for next working day delivery. Removing the wires without damaging the connectors is a simple method of enabling users to switch the polarity of actuator wires without needing to obtain additional Molex connectors or Molex housing. Cable, Connector & Crimping Tools Insertion & Extraction Tools Molex Crimp Extraction Tool, HANDTOOL Series, Pin, Socket Contact. Molex Crimping Tools provide excellent performance for reliable electrical connections. Once the header pins push back the hooks, Molex connector pin removal is simple, and the wire can slide out of the housing by pulling back on it without causing any damages to the power connector. This item: Knoweasy Micro Connector Pin Crimping Tool - Compatible with D-Sub, Molex, JST, and JAE Connectors - 32-20AWG / 0.03-0.52mm - Perfect for Wire Crimping and Electrical Repairs 25.99 25. ![]() This is completed by pushing the header pin into the thin gap between the metal power connector and the plastic on both sides of the housing. In this tutorial, we are using flat header pins that are used to release the hooks. Since there are two hooks keeping the connectors in place within the housing, they will need to be pushed back to release the wires. ENGINEER PA-24 Micro Connector Crimping Pliers for Molex, JST Connectors (AWG 32-18) (Made in Japan) iCrimp Mini Micro Open Barrel Crimping Tools Works on AWG28-20 JAM, Molex, Tyco, JST Terminals and Connectors used for FPV, Drone Servo. Part 3: Removing Wires with Crimped Power Connectors from a Housing However, there is a method of removing the wire from the housing without damaging the power connector. Once the crimped wire has been inserted into the housing, it will be difficult to remove. The power connectors have hooks that allow the connectors to latch into the connector housing. To disconnect a Molex connector (male and female connection), simple press down on outside clip and pull the connectors apart. Crimping with a manual hand tool, semi-automatic press and die, or fully automatic wire processor, all involve different levels of variability. Try crimping the wire again and inspect the crimp before inserting it into the housing. If the power connector pulls out or the wire comes loose, it means that your crimp was faulty. There are two housing options available, namely, a male housing (female power connectors) and a female housing (male power connectors). ![]() For example, a Progressive Automations control box may require the actuator wires to have a designated orientation to obtain an extend and retract sequence that correlates to the ‘up’ or ‘down’ activation buttons on a wireless remote. The orientation of the wires can be based strictly off preference and will depend on the Molex wiring required for the type of system that you are working with. ![]() The crimped wires can now be fed into the connector housing. Part 2: Adding Wires with Crimped Power Connectors to the Connector Housing Clamp down on the crimping tool and release.Įnsure the correct power connector is crimped onto the wire depending on if you use Molex connectors that are male or female. With the stripped wire inserted into the un-crimped power connector, load it into the crimping tool.Īlternatively, insert the un-crimped power connector into the crimping tool without the wire, and then feed the wire into the connector (either way works). MOLEX has set the specifications for almost all connectors and crimp terminals in. Therefore, the optimal length of exposed wire is 2.5 mm (the length of the crimp zone). MOLEX stands for no compromise in the world of crimp terminals and connectors. The amount of exposed wire should not exceed the length of the power connectors insulation and crimp zone, which is 5mm. Molex accepts no liability for connector performance or tooling support where tooling other than Molex Tooling is used or where Molex Tooling is modified.Part 1: Stripping the Wire and Adding the Power Connectorsīegin by using a wire stripping tool to strip back enough wire, ensuring proper connection when crimping on the power connectors. Extraction and Activation Tool: 0638132700: PremiumGrade Hand Crimp Tool for Female Terminals, 22-28 AWG: 0638192600: FineAdjust Applicator for 2.00mm Crimp Terminal, AWG 22-28: 0639007600: T2 Terminator Tooling Die for 2. When using tooling other than Molex Tooling with Molex specific connector systems listed in our ATS documents, the Molex tooling qualification does not apply and the responsibility for full qualification of the connector system is that of the customer. Hand Crimp Tool for 1.25mm Pitch Crimp Terminals, 26-32 AWG Wireįield Repair, See Tooling Specification (PDF) Above Type: 4DĬAUTION: Molex tooling crimp specifications are valid only when used with Molex terminals and tooling manufactured by Molex and sold by Molex or authorized distributors ("Molex Tooling"). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |